[Stealth Man]

Dan,

For exercising I wear a size tighter in girth and/or a size shorter in length so that retraction does not occur.

The Corkscrew will be quite obvious in your regular fitting pants. I will use mine mostly at home and for short outings in which I anticipate moderate activities and causal interactions. I wear an untucked shirt for complete privacy and occasionally without if I don’t mind drawing some attention 😉

You can also shorten the coil with a box cutter and use the PVC end cap that is included with the kit to seal. Experiment by removing one coil at a time until you find your preferred length. This will make for a lighter/smaller profile Corkscrew that is easier to put on to wear and conceal under loose clothing.

[Stealth Man]

I find that the glans temperature fluctuates and that it also has this capacity normally without the Stealth. I have been wearing for so many years now with no problems so I would be too concerned about it. However when it does feel cool or cold I will do some manual jelqs to engorge the glans and wear the Retainer Band at the base to maintain the effect.

[Stealth Man]

Hmnnn…. I have never experienced this so its hard for me to be able to make any comments as I don’t quite understand what is actually happening without said experience. I suggest you experiment with different adjustments and see what you can come up with for a solution. I have done extensive testing in hot and humid conditions without any serious problems so I think it may be more a question of fit rather than atmosphere.

[Stealth Man]

Yes we have shipped to Cambodia several times with no problems.

[Stealth Man]

If you are experiencing a drastic change in performance my first question would be if the baseband and sheath are set up correctly.  

When wearing the Innerwear the logo letters should be on top when looking down same as your regular under wear logo would be.

This requires that fold the base band twice so that the inside edge of the band is lined up with or overlapping the exposed seam where the single layer of material transitions to the double layer of the sheath section.

Guys often think that this seam is supposed to be facing inside. If you do this the silicone ring will face outside and it will not secure the penis into extension properly with a tendency to roll under and cause retraction and /or slippage.

• This reply was modified 6 years, 11 months ago by Stealth Man.

[Stealth Man]

I am not clearly understanding the pinching as you describe it Christian… can you be more specific. Not sure if it the skin or the hair or a combination of the two?

[Stealth Man]

yes if you are not sure nothing beats a direct comparison to know which is the better fit.

[Stealth Man]

great.. thanks for the update Christian!

[Stealth Man]

sure I can post a pic here for you…

[Stealth Man]

Hi Longon1980… welcome aboard!

We do see many guys upsize over time on subsequent orders. This can be attributed to gains made wearing the Stealth. For quicker more substantial gains inclusion of some regular PE exercises such as jelqs is recommended.

We will be having a range of more serious PE devices in the near future. These will be top quality at affordable prices and fun to use.

As you are borderline between the D and E series for length you could size up and see what you prefer. I also am between sizes and wear one or the other depending on how I am feeling and what sort of engagements I have lined up for the day.

[Stealth Man]

Yes I have also tried this with the larger girth Retainer Bands and it works well. The width is perfectly sized to fit inside the base band however to be completely concealed within the folds you must remove the snap buttons. Although you are getting the tighter fit with the band so the snaps are kind of redundant anyway. I tried to use the RB’s with the buttons installed but the hole it created in the rubber band caused it tear apart.

Why don’t you give me some details on your size and we will send you a couple of the larger sized Retainer Bands for testing out the idea for your feedback.

[Stealth Man]

No it really wouldn’t warrant a visit to the doctor as it is more of a mechanical issue. The solution is to really slow down the finish and take time to relax and eliminate 2-3 times extra. In cases of standing before the public giving a speech I would use the stall for privacy and remove the spandex sleeves and Retainer Band and maybe even the Innerwear to make sure that I have eliminated all the urine and then put my Stealth wear back on in full confidence. Definitely thats what I would do in such situations.

[Stealth Man]

Leakage can be a problem particularly when the fabrics are brand new and more so if the spandex sleeves and Retainer Band are also being used before they are broken in for a more relaxed fit. The trick is to not assume you are finished as usual (specially when rushed) but rather take an extra 2-3 “finishes” than you normally would. That means taking a moment to consciously relax the pelvic floor and then contract the PC muscle for complete elimination. Nothing worse than experincing leakage afterwards. You can also use the Retainer Band at the base of the shaft to act as a safely valve to prevents unintended urine flow if by chance you did not do so at the time.

[Stealth Man]

Agreed… we need to put up some actual clips to demonstrate the finer aspects of the recommended technique. This is something we will look into in the near future.

[Stealth Man]

The problem with snaps on top of the base band is that it would negatively effect the section of material leading to the sheath by creating unsightly bumps and lumps of excess material. We considered a wrap around velcro but that presents its own problems as well with hard edges that irritate the skin and pubic hair getting stuck up in the hook/loops.

The best solution for balls that want to retract is go for the sheath only version of Stealth however that means you forgo the option of having a ball strap at all. A simple hack you can experiment with is to use an elastic band would up to hold the base band at whatever tension you require.

[Author]

Posts