[Tekcon]

Excellent, thank you Stealth Man for that. I did in fact have them in the opposite position. They are now in the correct orientation. Thanks!

[Tekcon]

Hi Stealth Man,

No worries, I found a supply store that had a similar silicone tube that was slightly smaller than the tube used where the beads are able to slip on and be adjusted easily while unclasped a (straight line), and actually hold their position when clasped (circle).

I’m going to need a bit of clarification on your comment: “Before attaching the clasping beads on to the tube make sure that the N and S poles are in the correct alignment with the bottom magnet.”

I’ve lined everything up as well as I could compared to when I received it in the mail. I’ve got the bottom magnet centered, the two metal beads to the sides, and the clasping magnetic beads up top. There were no markings on the on any of the beads to indicate an orientation or alignment. Would it be possible to get a little more detail, or an image explaining this.

Thanks

[Tekcon]

Huh, I really wish I saw this thread before I went ahead and made my own modifications…

I don’t know how but I guess I really messed up on my measurement and had probably about 1.5″ to 2″ of silicone tube that basically had my mag-volt falling off. With no physical instructions to follow (and not thinking to contact support) rather than adjusting at the magnetic ends, I simply moved the bottom metal piece to one side, cut the silicone cord down the middle, and started making small incremental cuts until I had a balanced snug fit in both completely flaccid and erect.

The obvious downside to this method that the silicone tube will slightly pull out and constantly needs to be pushed back into the bottom metal piece.

Just need to find the width and order a new silicon cord and will cut it to the appropriate length and move all the important bits over to it.

[Tekcon]

@Whaim,

You should be able to wear the magvolt with the innerwear but it might be a little crowded. But, might be beneficial if you really want the bulge effect.

Probably not in their current design. When you order the magvolt you have to give Stealth a measurement around the genitals with an erection. My understanding is that it isn’t as elastic as the innerwear.

[Tekcon]

Yup, I contacted [email protected] a few days ago and I’m set to go. I got antsy and the support channel usually responds within 24 hours on a business day. Thanks Stealth Man!

[Tekcon]

@Stealth Man,

In regards to the Sabre Skin product, in the picture you posted a page ago it looks that is the Sabre Skin on top of the Extension Sleeve rather than Innerwear. Will the Saber Skin be a package deal (Extension Sleeve + Sabre Skin) or will it only be the Sabre Skin?

Just wondering as I’m getting to a point where the Innerwear has started causing some serious “rugburn” underneath the coin purse and was about to contact support to order the Extension Sleeve, but if it’s included with the Sabre Skin I’ll just wait until that is released.

Thanks

[Tekcon]

Same, put me down for 1 of each once it hit’s the site’s store.

[Tekcon]

Hiya Stealthman,

Checking in to see when we can expect to see the Extension Sleeve and TPE Sleeve will be available for ordering on the site. From your last post it sounded like these were incoming soon.

[Tekcon]

Yup, completely understand about that until the patents are a done deal and no worries about the wait.

[Tekcon]

Stealth Man, when can we expect to see some more info on the Vac hanger (pics, release date, pricing, etc.) If the production molds are underway, I’d assume soon?

• This reply was modified 6 years, 7 months ago by Tekcon.

[Tekcon]

The corkscrew can be a little bit intimidating at first, and it took me a good month of trial and error before i found the best way to wear it where i can wear it the longest amount of time. So don’t be afraid of wearing it for a few minutes, feeling discomfort and having to re-adjust it, it’s all part of the process. I’d say get use to wearing it in a location where you can make immediate adjustments on the fly. Don’t start going to work and getting stuck in a 2-hour meeting when you need to make an immediate change. I love wearing the corkscrew as part of my daily routine now.

[Tekcon]

For me I have the following issues:

– Stealth innerwear + wearing 2 sleeves + retainer band = leakage when flexing my PC muscle.

— FIX: Only wear 1 sleeve (preferably premium) and take off the retainer band prior to urination, flexing my PC muscle as much as possible after completion of urination, then putting back on the retainer band.

– Stealth innerwear + corkscrew = leakage when flexing my PC muscle.

— FIX: Prior to urination, I have to loosen the corkscrew enough that the proper flow of urine comes out, again flexing my PC muscle as much as possible after completion, then tightening of the corkscrew.

[Tekcon]

I originally ordered a size too small (my first stealth product) and went all in with premium sleeves and corkscrew, so I ended up having to get a larger inner wear shortly there after, but was still able to use the smaller corkscrew size.

I wear my innerwear and corkscrew anywhere from 8-12 hours a day, 7 days a week (with the occational day off every now and then). I got my corkscrew at the very beginning of February this year. Took me about a month of trial-and-error to figure out how to wear it comfortably (avoid circulation strangulation at the glands, skin burn, etc.).

I measured my bone-pressed stretched length (no to be confused with the length measuring for a steath innerwear) and my max stretch was around 7.25″ – 7.5″ depending on how loose my ligaments are at the beginning of the year. Now I’m able to get a good 8.0″ stretch. That’s about 2 months of consistent use.

I hope to get a month or so more in using the current corkscrew size until I need to order my next size so I can press on into 8.25″ stretched length territory.  I figure the E26 corkscrew will carry me into next year.

Of course everyone is different and mileage may vary.

[Tekcon]

I imagine the corkscrew will vary from size to size, I’ve got a D24 corkscrew and I’d say it’s ~1.5-2 lbs. I’ve gotten to the point I’ve outgrown it and need to order a  E26 corkscrew, so i’m looking forward to the extra size/weight.

If Stealth Man could provide a chart of size/weight for corkscrews that would be awesome 🙂

[Tekcon]

Thanks Stealth Man. That helps me make my purchase. Given the nature of the product, something doesn’t sit right with me trying to “re-sell” it. 🙂 Look forward to the Stealth branded hydro pump next year.

I don’t do any vac hanging, but given the success I’ve had with the inner sleeves and corkscrew i’m willing to give it a shot when released.

[Author]

Posts